2 AGA MINI AXLE SHAFT SEAL TOOL KIT Used to remove & replace the axle shaft seals without removing the transmission. For MINI R52, R53, R55, R56, R57, R58, R59, R60 & R61chassis with 6-speed automatic trans. (Qty.) (1) Block Cutter, (1) Center Punch, (1) Slide Hammer, (1) Center Mandrel, (1) Remover Screw, (1) Seal Installer, (1) Fill Plug Socket. 26 9975 010 $426.55 AGA BMW TIMING TOOL SET For setting camshaft timing on the BMW N63V8 engine. Contains: (Qty.) (1) Hold Down Bar, (2) Camshaft Plates, (1) Crankshaft Pin, (1) Crankshaft Holder, (1)Timing ChainTensioner, (1)Timing ChainTensioner Gauge, (1) Tensioner Locking Pin, (1) 8-12 mm Adapter. 09 9511 010 $470.25 AGA BMW VALVE STEM SEAL TOOL KIT Used to remove and replace the valve stem seals on the BMW N62V8 engine without removing the intake or exhaust camshafts. (Qty.) (2) Compression Rods, (2) Compression Nuts, (1) Rotator Handle, (3) Compres- sion Rod Feet, (1) Compression Block, (1) Compres- sion Lever Rod, (4) Camshaft Plates, (2) Camshaft Plate Bolts, (5) Brush Plugs, (6) Spark PlugTDCTools, (1)TDC Indicator, (1) Valve Keeper InstallTool, (1) Ratcheting Wrench, (1)Timing Chain LockTool, (1)Valve Stem Seal Pliers, (1)Valve Stem Seal Installer. 09 9973 011 $875.00 AGA BMW VALVE STEM SEAL TOOL KIT Used to remove and replace the valve stem seals on the BMW N63V8 engine without removing the engine or cylinder heads from the vehicle. 09 9973 020 $1059.99 AGA BMW & MINI WHEEL LOCK REMOVAL TOOL KIT Used to remove high security wheel lock with spinning ring on BMW and MINI vehicles, without the need of a key and leaving no damage to the wheel. Contains: (Qty.) (1) Collet, (1) Pin, (1) Remover. 55 6946 010 $369.55 AGA BMW SECONDARY AIR INJECTION CLEANER TOOL KIT Cleans the secondary air injection tubes and air passage on the BMW N62V8 engine without removing cylinder heads or engine from the car. Contains: (Qty.) (1) GuideTube with Handle, (1) Flex Cable, (2) Flex Cable Brushes, (1) Hand Brush, (1) Funnel, (1) Case. 09 9972 010 $249.00 AGA VALVE STEM SEAL TOOL KIT To remove/replace valve stem seals on BMW N63TU & S63TUV8 engines without removing the cylinder heads. Engine and transmission must be removed from the vehicle to perform this repair. Note: Also use:(Qty.)(2)11340039494valvestemsealkit,(1)11 127614700valvecovergasketset,(1)11127614701 valvecovergasketset,(2)11127588416highpressure fuelpumpgasket,(8)13537591006fuelinjectorgasket ring,(8)13537577649fuelinjectordecoupler. 09 9973 030 $1,690.00 800.203.9287 AGA BMW & MINI FUEL INJECTOR & SEAL TOOL KIT To remove fuel injectors and remove/install fuel injector seals on BMW N54 L6 & N63V8 engines, & MINI N14 & N18 L4 engines. (Qty.) (1) Fuel Injcr. Remover, (1) Fuel Injcr. Seal Remover, (1) Fuel Injcr. Seal Installation Sleeve, (2) Fuel Injcr. Seal CompressionTools. 09 0367 010 $280.25 REPLACEMENT INSERTS (5 PC) AGA-IHDTR-RI $23.00 AGA INJECTOR HOLD DOWN THREAD REPAIR KIT Having an issue with the injector hold down thread being stripped on N63/S63 engines? Fix it with AGA’s Injector Hold DownThread Repair Kit. Using a heat treated stainless steel insert, the thread can now be repaired using a guided fixture for the drill and tap for accurate angle. AGA-IHDTR-K $389.00